SC67-02 Original conveyance sensor (PS308) abnormality. Reply With Quote Sponsored Links 09-03-201206:43 PM #10 Michael Hay View Profile View Forum Posts Junior Member Join Date Sep 2012 Location Melbourne Australia Posts 13 Hi, I cannot The blade READY signal (READY condition) cannot be detected within a specified period of time after the blade replacement signal turns ON. SC36-06 Thermistor /4 (TH4) low abnormality detection (hardware). his comment is here
SC77-08 Stapler /Rr rotation abnormality (FS-604 only) SC77-11 The stapler motor home sensor / Fr (PS31) does not turn ON within a specified period of time after the stapler motor /Fr At this time, an error detection signal (blowout of ICP) is not detected. Have a manual for Konica Minolta Printers & Copiers? SC53-06 The blowout of a 12V ICP for the AC drive board (ACDB) is checked. http://www.copytechnet.com/forums/konica-minolta/37711-error-code-sc29-11-a.html
SC67-04 Non-volatile memory error. The compression processing from the page memory to the memory is not terminated within a specified period of time. Hide thumbs Also See for bizhub PRO 920 Operation manual - 978 pagesUser manual - 970 pagesManual - 18 pages 1 2 3 4 5 6 7 8 9 SC93-05 24V power source check.
SC18-40 The locking of the paper lift motor (M100) is detected. JAM CODE 443 Field Service Ver3.0 May.2006 TROUBLESHOOTING 12.JAM CODE 12.1Jam code list Classifica-tionJam codeCauseResultingoperationCorrectionBypassJ10-01 D u r i n g o p e r a t i o n The registration sensor (PS44) does notturn ON within a specified period of time after the SC18-11# When the upper limit sensor /1 (PS20) is OFF, PS20 does not turn ON within a specified period of time after the paper lift motor / 1 (M19) turns ON SC46-35 Sequentially shot page area abnormality.
what can I do......... Konica Copier Error Codes SC21-06 The locking of the transfer/separation cleaning motor (M18) is detected. SC41-02 When the speed of the polygon motor (M17) is being switched, a speed lock signal is not detected within a specified period of time. Hewlett-Packard CompanyBooks about SensorArduino by ExampleAutomotive Electronic SystemsInternet of Things with Arduino BlueprintsPhotodetectorsHall-Effect SensorsTransducer HandbookSensor Technology HandbookSensors for MechatronicsBuilding Wireless Sensor Networks Using ArduinoMeasurement and InstrumentationLearning ROS for Robotics Programming -
PDF Manual UserManual_English.pdf.... Also ensure your charge corona is seated correctly. al. SC90-01* Initial communication check between the ADU drive board (ADUDB)/ printer control board (PRCB).
When this condition is detected 5 times in succession, the error code is displayed. http://www.fixya.com/support/t14642660-konica_bizhub_pro_c_500_error_code_sc29 ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection to 0.0.0.10 failed. Konica Minolta Bizhub Error Codes Replacing the developer requires entering service mode, it also requires running the machine with the doors opened. While in the image read, the com-pression of image data that is read in is not correctly terminated.
Reply With Quote 09-02-201211:22 PM #2 Michael Hay View Profile View Forum Posts Junior Member Join Date Sep 2012 Location Melbourne Australia Posts 13 The code relates to a Dmax this content While in the drum potential correction, no convergence is obtained even after correction is made more than 10 times. SC49-07 The CF card in IC-203 is different from the program version of the hard disk /2 (HDD2). This abnormal condition recurs even a specified period of time after FM5/FM8 is turned OFF and then turned ON, and an error detection signal (blowout of ICP) is detected.
Auto adjustment monitor value abnormality. SC67-08 Tray up/down motor (M303) abnormality. SC42-05 The blowout of ICP for the write unit cooling fan /1 (FM5) in the AC drive board (ACDB) is checked. weblink And at this time, an error detection signal (blowout of ICP) is detected.
An abnormal condition is detected with the fusing error detection signal 4. SC67-03 Original reverse sensor (PS309) abnormality. Reply With Quote + Reply to Thread « km6500 & km6501 | Km5501 km 5500 ikon cpp550 cpp560 » Similar Threads SC45-20 Error Code.
The output voltage of the TH4 is detected as a low temperature (-6°C or lower) or high temperature (240.5°Cor higher) abnormality in the comparator circuit. An abnormal condition occurs with the FM3 and FM4 EM signal a specified period of time after FM3 and FM4 turns ON. SC42-16 The rotation of the polygon cooling fan (FM9) is checked and the 24V power source is also checked. An abnormal condition occurs with the FM7 EM signal a specified period of time after FM7 turns ON.
TH1 does not get to 50°C when a specified period of time elapses after the main power switch (SW1) is turned ON for the fusing ON control. PS11 does not turn OFF within a specified period of time after the reverse operation (return operation) is started. While in the drum potential correction, no convergence is obtained even after correction is made more than 10 times. http://wx2me.com/error-code/sc-error-code-6-gle-error-code-52.php i hope a proper calibration will make me happy.
After a separation error detection signal is detected while in the separation ON, up to 5 separation ON/OFF operations occur in succession. PDF Manual UserManual_English.pdf.... SC46-82* The ID of the task that sends the message queue is undefined. To print the manual completely, please, download it.
SC28-01 A charge leak is detected. Ronald el código sc 24-03 bloque la maquina al momento de encender la maquina sale ese error ya prove las fuentes la tarjeta principal la tarjeta de imagen en otra maquina SC46-32* While executing the APC, the execution of the MPC is attempted. Loading...Oops :Please try again.
An abnormal condition occurs with the FM12 EM signal a speci-fied period of time after FM12 turns ON. SC21-02 The blowout of ICP for the charge cleaning motor (M23) in the printer control board (PRCB) is checked.