I could be that your files just got mixed up with someone elses. Don't know if this is the final fix but... After that message, i get the error code 1009 and it says that there is no tune changes written. SAP rear spoiler. this content
SCT is closed for the memorial weekend and isn't open till tues. From what Ford and most everyone else says ECUs almost never go bad 5. Today 09:06 AM by diselfan 5 Using anti-gel Today 08:59 AM by diselfan 2 A good cold air intake Today 08:47 AM by diselfan 7 Truck wont rev past... If you are running a larger than stock MAF, you may see this problem. http://comphelp.org/guide/sct-tuner-error-code-1009/
Last of the Hatches #28 To view links or images in signatures your post count must be 10 or greater. Email Address: OR Log-in User Name Password Remember Me? So I scaled my Engine Displacement down by 30%, and my Load came in at 1.3, which is about right for my setup. Could I be over loading that circuit?
Results 1 to 12 of 12 Thread: SCT Tuning HELP! It would be great if their stuff worked EVERY time! Today 03:07 AM by junior125 1 Early '99 AC Wiring... Sct Flash Is it tuned or just married?
Because everything works until I turn the key on and that is when the shift light cycles and the wideband does. If your load comes out too low at the top of the WOT run, check to see about how much you needed to scale down your MAF Transfer Function from the Its fustrating to deal with SCT and the buggy software, especially when it makes cars not run. [email protected] Tuners03-14-2011, 03:45 PMYou will have to call up SCT to get it straightened out.
Today 02:42 AM by IsraelSalinas 16 Anyone having problems... I never tap anything off the ecu power wire. You have an SVT which has always been problematic flashing. I called SCT and they told me that it somehow "glitched" and didn't install one of the drivers.
So lets hope that it just works and I am going to try to just remove those wires just to make sure. http://powerstrokearmy.com/forums/showthread.php?t=26767&showall=1 Then my max load was only 0.9. Sct Tuner Error Codes SUCKS. Sct X3 Unlock Ecm Failed User Name Remember Me?
FR Susp/Struts. news I went to upload my tune and my tuner came up and said error 1019 ecm locked or something like that. I knew it was used but... Today 03:34 AM by sonicnofadz 5 Air intake benefit with... Sct Updater
Codeman03-21-2011, 02:43 AMOk well I have a question. Does the job! Car has been sitting for 2 weeks now since SC install complete but can't drive cause NO TUNE!! have a peek at these guys Did you by any chance update the firmware on the SCT before you returned your car to stock?
It won't even let me return the vehicle to stock. Reply With Quote 03-11-2011,10:01 AM #4 myrsvt View Profile View Forum Posts View Blog Entries View Articles Rookie SVT Poster Join Date August 2009 Location Myrtle Beach, SC Posts 85 Ok, Email: To view links or images in signatures your post count must be 10 or greater.
Sign In Sign Up Browse Back Browse Forums Gallery Blogs Tutorials Garage Calendar Videos Chat Donations Staff Online Users Activity Back Activity All Activity My Activity Streams Unread Content Content I Make sure no chip is in J3 port on rear of ECU in order to flash 3. Did you recently update the sct device before this happened? Whatever program is in the EEPROM will become the stock download program in the SCT X3. (only one program at a time is ever stored in the ECU) 4.
Note that passwords are case-sensitive. I don't know but I hope that is the reason I have been having so many problems. Join Date: Jul 2007 Location: Ft Lauderdale, FL Posts: 3,109 Re: SCT wont load into my truck What is the exact message? http://wx2me.com/error-code/sc-error-code-6-gle-error-code-52.php I plan on taking the ECM out tonight to confirm.
Tried it out and still getting same errors...starting with the "Unlock ECM Failed" SCT said they replaced the board and I did check for the 18volts on pin 13 to the Got tuner back from SCT yesterday. Eli Kline is offline Quote Quick Reply Remove Advertisements Sponsored Links Ford Mustang Forum Advertisement Reply vBulletin Message Cancel Changes Quick Reply The following errors occurred with your Customer Support AIM: hpdyno Email: To view links or images in signatures your post count must be 10 or greater.
The system returned: (22) Invalid argument The remote host or network may be down. I wish they would just stick with one. so i should check to make sure i got the computer code write and if its tunned for a automatic which is what i have. I checked and I have .4 volts with key on.
http://www.svtperformance.com/forums...cm-failed.html This guy said the key was in the wrong position.. This thing is JUNK!!!!!!!!!! -------------------------------------------------- Donnie... 06 F350 Harley leveled ang exhaust. This sucks. problem solved 09 F450 CC LB lariat 6.4 black on black 23k miles, stock.. (For now)... 97 F250 SC LB 4x4 7.3 05 Superduty axels, 18" King Ranch Rims, "under the
A 3015 supports that. Or i'm looking at maybe ECU is screwed up and sending/receiving wrong voltage?? PSDPlayer is offline Quote Quick Reply Go to the Top Reply Page 1 of 2 1 2 vBulletin Message Cancel Changes Quick Reply The following errors occurred with Join Date: Jul 2007 Location: Ft Lauderdale, FL Posts: 3,109 Re: SCT wont load into my truck Seems like you bought that thing used.
Reply With Quote 04-24-2011,11:41 AM #11 mwolson View Profile View Forum Posts View Blog Entries View Articles Gray beard Join Date March 2004 Location San Jose, CA Posts 3,322 I have Go into device info and tell me what the device status is.