Contact your International Distributor for more information. Min. Either the cylinder or head bytes did not match. SMART errors reported by the BIOS and third-party utilities after Seatools passes all tests My system reported a S.M.A.R.T. have a peek at these guys
Min. This status code is obsolete starting with SAM-4. 18h Reservation Conflict The target returns this status code if an initiator attempts to access a LUN that has been previously reserved by Please join our friendly community by clicking the button below - it only takes a few seconds and is totally free. Meaning of Bytes Passed In/Out Cmd/ Data 0 0 Data out of host. 0 1 Command byte out of host. 1 0 Data to host. 1 1 Completion status byte to http://knowledge.seagate.com/articles/en_US/FAQ/206595en
A FIGURE 21: Opcode 04: Format Drive BIT BYTE 7 6 5 4 3 2 1 0 0 0 0 0 0 0 1 0 0 1 LUN Head Number 2 ST11R Controller Product Manual, Rev. The entire disc should be formatted with the same interleave factor. (See Section 7.0) 6.1 .9 CONTROL (BYTE 5) This field contains the control bits that tells the controller how to Sign Up Now!
What is Error Recovery Control? 8-digit (eight digit) diagnostic error code: Sometimes Maxtor OneTouch software or FreeAgent software gives an 8-digit (eight digit) diagnostic error code after a diagnostic test. I assume that that's the one I'm using (and have previously used many times without any problems on several 80 GB disks). A 4.2.4 RESULT PHASE In this phase, ready will be 1, C/D will be 1, and I/O will be 1. Seagate Support When ready is one, bits 1 & 2 are interpreted as follows: * Active only if enabled in control register.
A CONTENTS 1.0 GENERAL PRODUCT DEFINITION AND INTERFACE SUMMARY 1-1 1.1 DMA or Program I/O 1-1 1.1.1 Interrupt Generation 1-1 1 .2 Automatic Seek and Verify 1-1 1.2.1 Fault Detection 1-2 Seatools Test Code Meaning I downloaded it from here (or from some similar URL - M$ keep changing them, to keep us on our toes):
Min. Seatools For Windows The controller does not perform any write operation during this command. Max. t3 address hold 20 ns.
The system returned: (22) Invalid argument The remote host or network may be down. Seagate reserves the right to change, without notice, the specifications contained in this manual. Seagate Seatools Error Codes List The default is IRQ5. Error Code Mac A FIGURE 38: Opcode E3: Drive Diagnostic BIT BYTE 7 6 5 4 3 2 1 0 0 1 1 1 0 0 0 1 1 1 LUN 0 2 0
It's a boot CD with 101 > disk tools including partitioning tools, MBR tools etc, and some "souped > up" versions of fdisk. More about the author Neither the BIOS or software driver are presently available from Seagate. 1.2 AUTOMATIC SEEK AND VERIFY A seek command is implied in every data transfer command. FIGURE 41: Opcode E6: Write Long BIT BYTE 7 6 5 4 3 2 1 0 0 1 1 1 0 0 1 1 0 1 LUN Head Number 2 Cyl. It does a read verify sector 0 on all tracks sequentially. Seatools For Dos
Min. The corrupted system files entries can be a real threat to the well being of your computer. ii ST11R Controller Product Manual, Rev. http://wx2me.com/error-code/seagate-error-code-12h.php Host software is responsible for insuring that deleted tracks are never accessed. 1C Alternate track not flagged as an alternate. 1E Illegal access to an alternate track. 1F Recovery mode not
It con- tains 8-bit data paths. The ID bytes are written with the ID of the actual alternate track. ST11R Controller Product Manual, Rev.
This Seagate Error Code 40h error code has a numeric error number and a technical description. A completion status byte will be loaded into the data I/O register. About Us TechieHQ is your source for tech support and computer help. The bits can contain one of the following: 00 Drive-related errors 01 Controller-related errors 10 Command-related errors 11 Miscellaneous errors Error Code (Bits 3 to 0): This describes the actual error
A 6.1.8 INTERLEAVE (BYTE 4) This field specifies the interleave during the Format operation. Number of Cylinders low 2 Max. It contains controller status bits that enable the host computer to monitor the status of the controller during command execution. http://wx2me.com/error-code/seagate-error-code-0-h.php A 4-1 Write Control bitO + Enable DMA bit 1 + Enable Interrupt bit 2 - bit 7 not used 4.1-1 DATA INPUT/OUTPUT REGISTER (DIOR) Disc read/write data, command bytes, completion