No, create an account now. Could the parity be build invalid if this drive fails in the process?I'm scared of using these "problem drives", but I'm not that fond of getting a new drive EVERY time Retrieved 12 July 2016. ^ "9154: S.M.A.R.T. failure and errors, Western Digital. http://wx2me.com/error-rate/seek-error-rate-200.php
August 2010. Text is available under the Creative Commons Attribution-ShareAlike License; additional terms may apply. parameter indicates a number of flash erase command failures. 177 0xB1 Wear Range Delta Delta between most-worn and least-worn Flash blocks. Normally this attribute value should be equal to zero and if the value is far above zero, then most likely there will be some serious problems with power supply or an navigate to this website
The actual storage medium (the disk drive platters) are fine, but for whatever reason the mechanical system that drives the read heads is degrading in some manner. The ones to really monitor closely are the reallocation sectors and pending reallocated sectors (#5 and #197), When they start to go up, you need to monitor them closely, and if I have read where a drive manufacturer will refuse to RMA a drive if their diagnostic software shows a good drive but you can always contact the computer manufacturer and express Back to top #8 signofzeta signofzeta Topic Starter Members 416 posts OFFLINE Local time:08:25 AM Posted 27 July 2014 - 07:14 PM I performed the smart check and short drive
Monitoring. Connect with top rated Experts 21 Experts available now in Live! So far, the reallocated sectors count, current pending sector count, and the uncorrected sector count, the read error rate, write error rate, seek error rate are all at 0, and has Hardware_ecc_recovered If the problem follows the drive the drive is the problem.
I do not know why you are getting that message.In all of these scenarios there are two possibilities - either there is truly an issue with the disk itself, or there PRTG is easy to set up & use. Retrieved February 3, 2006. http://lime-technology.com/forum/index.php?topic=32681.0 I use the results of this to decide if the disk is OK or whether the drive really needs replacing.
Not drive related?Looks like disk 10 timed out and refused to reconnect. What Is Raw Read Error Rate The HDIO errors are a result of the drive never responding to controller reconnect attempts, so those errors are a result of the drive not being properly recognized. Yes, my password is: Forgot your password? Some are pretty tight together, does it help to just loosen them?I'm rebuild of my server and that puts the project back to the drawing board.
It decreases while the NAND erase cycles increase from 0 to the maximum-rated cycles. 234 0xEA Average erase count AND Maximum Erase Count Decoded as: byte 0-1-2 = average erase count https://en.wikipedia.org/wiki/S.M.A.R.T. Some codes are specific to particular drive types (magnetic platter, flash, SSD). Seek Error Rate Fix Technical Report SSF-8035, Small Form Committee, January 1995 ^ Seagate Product Marketing (1 July 1999). "Get S.M.A.R.T. What Does Seek Error Rate Mean As manufacturers do not necessarily agree on precise attribute definitions and measurement units, the following list of attributes is a general guide only.
Acronis Knowledge Base. Smartmontools. I use crystaldiskinfo to take a look at my s.m.a.r.t attributes, and here is a screenshot of all the smart attributes. http://wx2me.com/error-rate/seek-error-rate-wd.php How does smartmontools differ from smartsuite?, SourceForge.
Please note that we cannot individually respond to all comments. Seagate High Seek Error Rate Not drive related? CONTRIBUTE TO OUR LEGAL DEFENSE All unused funds will be donated to the Electronic Frontier Foundation (EFF).
the other drives are looking ok though so my chances of 2 dieing are still not too high. Micron Technology, Inc. How to predict hard disk failure (SMART Report), 2010-05-19 with Palimpsest (originally by Red Hat) KB251: Understanding S.M.A.R.T. Head Flying Hours Thus, the higher the attribute value, the more sectors the drive has had to reallocate.
An increase of this attribute value is a sign of problems in the hard disk mechanical subsystem. 12 0x0C Power Cycle Count This attribute indicates the count of full hard disk error at all, except the temperature, meaning that S.M.A.R.T. Retrieved 2014-03-31. ^ "Problem with hard drive clicking", Think (wiki) ^ "hdparm(8) - Linux manual page". my review here In the case of the G-sense error rate, you want a lower value, and I think it is normal for the G-sense error rate to increase, but I don't know if
The factory default is eight (8) seconds, which is a very poor choice for use with Linux. Back to top BC AdBot (Login to Remove) BleepingComputer.com Register to remove ads #2 JohnC_21 JohnC_21 Members 14,728 posts OFFLINE Local time:09:25 AM Posted 27 July 2014 - 12:45