The monitor set name may be shown as monitor set. Be sure that the file is larger than size-extracted-and-output-in-bytes and no more than the valid size of the data that was written. The command will not terminate abnormally as a result of this warning. (O) Re-evaluate the values specified in the environment parameters file. Possible causes of this error are as follows: The file or directory does not exist (when an existing file is opened). https://scn.sap.com/thread/1984177
When this error occurs subsequent to startup processing (during operation): Continues monitoring. If this does not resolve the problem, collect maintenance data and then contact the system administrator. KAVF14210-I The command ended normally.
This message immediately follows the KAVF14220-E and KAVF14221-E messages that provide the name of the function resulting in the error and detailed information. Please try again. A large volume of performance data was acquired, and a large amount of is required for the SAP system or PFM - Agent for Enterprise Applications to process it. http://www.sapdatasheet.org/abap/msag/tpda-151.html The system then cancels execution of the command. (O) Check the destination specified as the RFC connection information to re-evaluate the operating status of the SAP system and the network status,
Commands. of object instance or reference TPDA 850 Specify a watchpoint variable TPDA 851 Watchpoint created TPDA 852 Specify the program in which the watchpoint is to be active TPDA 853 Program For details about how to collect maintenance data, see the chapter that describes error handling procedures in the JP1/Performance Management User's Guide. Refer to your operating system documentation for further details.
Check the KAVF14171-W message output after this message for the performance data that was not acquired. (O) If the problem occurs frequently and the errors are not resolved, collect maintenance data http://webclient2.rssing.com/chan-7561141/all_p197.html You can check the monitor set name by means such as transaction code RZ20. For that i have a button in view1. I have created a button in view1 and im trying to navigate from view1 to view2.
If you are omitting the arguments, make sure that the following items are defined correctly in the TARGET section of the environment parameters file: Monitor set name (MONITOR_SET) Monitor name (MONITOR) We still don't know who call it. shared memory does not exist: The shared memory does not exist. Quality and Logistics) i can't.
This message follows the KAVF14220-E message. the CRT libraries are not installed: One or more required CRT libraries are not installed. They will look into it after the upgrade. Pipe I/O returned 0 bytes Mar 19 07:50:33 2002: Backup Server Internal Error: 188.8.131.52: Multibuffering subprocesses died, archive /home/copias/abr19.dat.
At this point, all collection-related initialization processing has been completed. (S) Collects performance data. This report page is a snippet summary view from a single thread "Error during upgrade in MAIN_SHDRUN/ACT_UPG", located on the Message Board at http://scn.sap.com. This message is displayed the first time the command is executed with the -lasttime option specified (when the specified timestamp file does not exist).
Before correcting an error in the connection parameters in the Agent Collector service startup initialization file (jpcagt.ini), check if PFM - Agent for Enterprise Applications was stopped by the jpcspm stop Attempted to write 55296 bytes, 4095 bytes were > > written. > > Mar 19 07:50:33 2002: Backup Server: 184.108.40.206:  Error for device > > '/home/copias/abr19.dat'. The following error is thrown by SUM in Preprocessing Phase. Checks after phase MAIN_SHDRUN/ACT_UPG were negative! ERROR : Detected the following errors: # /usr/sap/HRE/SUM/abap/log/SAPA742EPU.HRE: 1EEDO519X"DB Prozedur Proxy" "PPH_V02_MRP_CHECK_SEL" Calling the BSP page was terminated due to an error.
we have done the setup by following SAP NOTE : 1832481. Checks after phase MAIN_SHDRUN/ACT_UPG were negative! The system postpones updating of the performance data that was supposed to take place at this time. (O) When this error occurs during startup processing: Check the version of the SAP But when the breakpoint stops, it is already inside this function module.
I can start the debugger, but few steps through and error message occurs and I'll have to start all over again.Are you encountered similar problem? wiki Date Views Headline Answers 09.12.2011 120 BAPI_SAG_GETDETAIL Error 6 01.03.2012 236 Syntax error in program "SAPLJ_1B_NFE_IN ". 8 16.09.2011 212 Message no. Error "Error during quantity posting for inspection lot, manual proc. If you do not specify an environment parameters file with the -cnf option, the default environment parameters file (command-name.ini in the current directory) is referenced.
It will stop at every 'CALL FUNCTION' statement. For details about the specification of the called BAPI, see the documentation for the SAP system's object navigator (SE80), BAPI browser (BAPI) or the SAP system. (S) Cancels execution of the Mar 19 08:04:32 2002: Backup Server: 220.127.116.11: Dumpfile name 'dteam040210906AF9' section number 0001 mounted on tape drive '/dev/st0' The OS is Unixware 7.1.1., ASE 11.9.2 and the tape is a a We already successfully replicated material masters to CRM (using R3AS and object MATERIAL).
There is a problem in the network settings. Breakpoint will stop at line 575 of program SAPMSSY0. If any of the unreported information requires an action, take the appropriate action according to the stored CCMS Alert Information. KAVF14128-E Cannot log on to the SAP system. (name-of-the-function-resulting-in-error) A logon error occurred during connection establishment with the SAP system.
If the BAPI_XMI_LOGON function module resulted in an error during authorization checking, grant the SXMI_PROD authorization object to the user being used for RFC connection. Error writing to archive device > > /home/copias/abr19.dat. Mutually-exclusive options are specified. So, i can now ignore the error and proceed with the upgrade.