Your description looked to be the exact issue that I'm having, up until the very last screenshot: I only have one entry for http. ,mpsetup.log shows that the mp installation was Possible cause: The designated Web Site is disabled in IIS. I've been holding out to install SP1 once its RTM... Type the following command, and then press ENTER:cd C:\WINDOWS\Microsoft.NET\Framework\v2.0.50727 3. his comment is here
Thanks, Andrew January 16th, 2008 2:55am Srikanth (or anyone on the OSD team), I to am expierencing the same issue on my customer's new production install. In the parent folder to the sharw where the SMP is located, grant the Network Service Full Controll ACL permissions to the parent. SMS-services run as local service We have the exact same setup at another customer with the same rights and it works over there. May 9th, 2008 2:00pm I tried that, and it didn't work... navigate to this website
The http status code and text is 500, Internal Server Error. Also got this up on technet... :http://social.techne...82-9ae6ba716c6d ____________________________ Errors: On SMS_STATE_MIGRATION_POINT: SMP Control Manager detected SMP is not responding to HTTP requests. When I tried to use the FQDN, I couldn't connect to the share either. Register now!
Right-clikc and Sharing and Security 5. Comment by Andrew -- April 27, 2013 @ 8:59 am | Reply RSS feed for comments on this post. Possible cause: Internet Information Services (IIS) isn't configured to listen on the ports over which SMS is configured to communicate. Readmpstringsettings(): Regqueryvalueexw() Failed - 0x80070002 Grant Full Control 2.
Generated Thu, 27 Oct 2016 08:25:45 GMT by s_nt6 (squid/3.5.20) Add back the reporting point.7. tools show folder size SCCM OSD Basic troubleshooting mplist procedure reports error but mpcert and mpli... Finally I realised that I was using the Netbios name of the server to connect to the store share, but SCCM was using the FQDN.
When I go into ConfigMgr site system Properties, both of the FQDN (intranet and internet are blank). [The Name is \\netbios; sitesytem type: Windows NT Server] If I restart the server Possible cause: You took the site system out of service and do not intend on using it as a site system any more.Solution: Remove the site system from the list of Free Windows Admin Tool Kit Click here and download it now May 12th, 2008 10:52pm And you assigned the web certificate to the various roles in IIS. This is basically to determine if the ISAPI is in healthy condition.Tom, can you attach the smpisapi.log, I would like to investigate it further to determine this odd behavior.Thanks,Srikanth Free Windows
I mapped it as a drive and navigated to the migrationstatus.xml file and opened it using notepad to verify that the correct ACL's were in place. http://windows7sux.blogspot.com/2009/04/sccm-smp-500-error.html Solution: Verify that the designated Web Site is configured to use the same ports which SMS is configured to use. Sccm 2012 State Migration Point Logs Thank you so much for your time. Http Test Request Failed, Status Code Is 500, 'internal Server Error'. Solution: Verify that the designated Web Site is enabled, and functioning properly.
To enable the 64-bit mode, type the following command, and then press ENTER:cscript %SYSTEMDRIVE%\inetpub\adminscripts\adsutil.vbs SET W3SVC/AppPools/Enable32bitAppOnWin64 0 3. http://wx2me.com/sccm-2012/sccm-pxe-certificate-error.php Possible cause: The designated Web Site is disabled in IIS. You need to find it out first from IIS configuration. For more information, refer to Microsoft Knowledge Base. \ / / \\\' , / // \\\//, _/ //, \_-//' / //<, \ /// > \\\`__/_ /,)-~>> _\` \\\ (/ \\ //\\ Call To Httpsendrequestsync Failed For Port 80 With Status Code 500, Text: Internal Server Error
Where do i configure the ports SMS communicate with IIS?ThanksAndreas Scheer September 20th, 2007 10:44am Andreas, the error you are getting is an internal server error. Home Forum Archives About Subscribe Network Steve Technology Tips and News State Migration Point Problem Hallo,I have SCCM 2007 RTM everything is working, but i get this error from Component 'SMS_State_Migration_Point': May 12th, 2008 10:06pm Correct, we are in native mode... weblink the above certs are all from that PKI and can be found in the SCCM local computers personal certificates.
Maybe I setupsomething up incorrectly? Free Windows Admin Tool Kit Click here and download it now May 9th, 2008 9:14pm I did one other step. Issue 3: Management Point and/or State Migration Point are failing to install, and you see status messages like “SMS Site Component Manager failed to install the component on this system” Issue
Search for: WMUG Community Contributor Blogroll ConfigMgr Support Team Blog Daniel Ratliff Gerry Hampson Jason Sandys Johan Arwidmark Kent Agerlund Niall Brady - Windows Noob Nikolaj Andersen Peter van der Woude MP, SMP? Comment by Tarkan Koemuercue -- May 12, 2011 @ 7:08 am | Reply You are a golden god. no errors in the status messages), requesting a State Migration Point fails on the client.
Issue 2: SMP is not working, and you see Status Messages like “SMP is not responding to HTTP requests. The http status code and text is 500, Internal Server Error.” Issue State Migration Point Operation Common Issues with MPs and SMPs The following is a list of common MP and SMP issues, and suggested resolution of these issues. This is not to Click Start, click Run, type cmd, and then click OK. 2. check over here E.G. "net use \\
The storage object has been inaccessible since "5/9/2008 5:00:02 PM". Stop and start the smsexective service on the SMP. You can issue the following URL in a browser to check the Management Point list for the site. Possible cause: The SMS ISAPI Application Identity does not have the requisite logon privileges.
It will take about 20 minutes for the normal HTTP 200 messages from coming in, but it should work and communications should resume with your clients. " #2 Jean Total Remove IIS 3. The http status code and text is 500, Internal Server Error.