Right-click the library, and then click Update Barcodes.A message appears that asks you if you want to continue. For any application that cares, it looks like a dual ported SAS disk accessed via the primary port (relative target port 1). M - Media Changer Device (SMC-3) . . .A - Storage Array Device (SCC-2)SBC) . . . The driver can also be used to simulate very large disks, 2 terabytes or more in size by "wrapping" its data access within the available ram. this content
If this position does not match what NetBackup has calculated the position should be, then the job will fail with a media write error. If a full rewind has occurred, E - SCSI Enclosure Services device (SES-3) . . . ASCQ DZTPROMAEBKVF Description 11/00 DZT RO BK UNRECOVERED READ ERROR 11/01 DZT RO BK READ RETRIES EXHAUSTED 11/02 DZT RO BK ERROR TOO LONG TO CORRECT 11/03 DZT O BK MULTIPLE Right-click the selected media, and then click All Tasks | Delete.
P - Processor Device (SPC-2) not blank = code used . .R - C/DVD Device (MMC-6) . . Check to see if a tape is loaded. V - Automation/Device Interface device (ADC-4) . . . . ASCQ DZTPROMAEBKVF Description 21/00 DZT RO BK LOGICAL BLOCK ADDRESS OUT OF RANGE 21/01 DZT ROM BK INVALID ELEMENT ADDRESS 21/02 R INVALID ADDRESS FOR WRITE 21/03 R INVALID WRITE CROSSING
Even if it did, making them truly unique in a virtual driver, especially if multiple boxes could somehow see each other, would be difficult. Rather than mounting the pseudo disk, the sg3_utils package could be used to carry out various tests on it. P - Processor Device (SPC-2) not blank = code used . .R - C/DVD Device (MMC-6) . . Scsi Sense Codes Decoder By default when loaded it has one scsi device (owned by a host).
Right-click the appropriate library, and then click Properties.The Properties dialog box appears. Scsi Error Codes E - SCSI Enclosure Services device (SES-3) . . . From the CommCell Browser, right-click the appropriate storage policy copy, and then click Properties.The Copy Properties dialog box appears. https://en.wikipedia.org/wiki/Key_Code_Qualifier Once the command count reaches
P - Processor Device (SPC-2) not blank = code used . .R - C/DVD Device (MMC-6) . . Scsi Status O - Optical Memory Block Device (SBC) . . B - Simplified Direct-Access (Reduced Block) device (RBC) . . . .K - Optical Card Reader/Writer device (OCRW) . . . . The opts "medium error" flag will cause any read command whose range of sectors includes sector 0x1234 (4660 in decimal) to return a medium error indication to the mid level.
O - Optical Memory Block Device (SBC) . . V - Automation/Device Interface device (ADC-4) . . . . Scsi Sense Key Check the Library Information and make sure that the drive count is correct and that the serial number is visible. Scsi Command Codes If the the virtual_gb parameter is changed (via sysfs, after the driver has been running), then the "Capacity data has changed" UA condition is set.
T - Sequential Access Device (SSC-5) blank = code not used . news E - SCSI Enclosure Services device (SES-3) . . . F - Object-based Storage Device (OSD-2) ASC/ . . . . . When the library is online, perform a full scan of the library. Scsi Check Condition Codes
Note that if any of these three parameters is set to zero at kernel boot time or module load time then no devices are created. No Yes Index ? switches), HBAs or the physical drive/library. have a peek at these guys You are running it in interactive mode.
V - Automation/Device Interface device (ADC-4) . . . . Scsi Unit Attention In this case, contact your library hardware vendor. Tape block size (e.g 65536 or 64k):  Press Enter.
Links | Press Releases Disk Survey Surveying the disks of the world RSS Blog Archives Survey site Knowledge Base Contact Understanding SCSI Sense This page is about decoding and interpreting the Solution It is important to understand that NetBackup does not write data directly to a tape drive. B - Simplified Direct-Access (Reduced Block) device (RBC) . . . .K - Optical Card Reader/Writer device (OCRW) . . . . Scsi Code Enter the file marker for initial positioning:  0 Press Enter.
A disk can reassign the affected to solve the problem. a disk) to report to the originator (e.g. A link to a TechNote for documentation on Robtest is available at the end of the TechNote. http://wx2me.com/scsi-sense/scsi-medium-error-03h.php Product Security Center Security Updates Security Advisories Red Hat CVE Database Security Labs Keep your systems secure with Red Hat's specialized responses for high-priority security vulnerabilities.
O - Optical Memory Block Device (SBC) . . the (pseudo) disk) is the application tag owner. Method 2 Use this method if you want to change the barcode format. Learn more Special Deals!
Error Code 62:305: Tape volume block size selected is not supported by the underlying HBA card. switches), HBAs or the physical drive/library. Unix servers require a passthrough driver. Cause After a library firmware is upgraded or restarted, the library reports all media with different barcodes than prior to the upgrade or restart. Attempting to move the tape using robtest produced the following error: m p1 s28 Attempting to move the tape in port 1 of the CAP to slot 28 Initiating MOVE_MEDIUM from
V - Automation/Device Interface device (ADC-4) . . . . NetBackup has no understanding of tape capacity. In the Load Media dialog box that appears, select the appropriate MediaAgent, Drive Pool, and Drive, and then click OK. Using the MediaAgent Log onto that MediaAgent either remotely or directly.
The formula is "((hostno + 1) * 2000) + (target_id * 1000) + lun)".