You get different addresses on different servers because the same device (or a device on the same switch port or FA) will have different addresses on each machine. IanWorthington, May 9, 2014 #18 (You must log in or sign up to reply here.) Show Ignored Content Share This Page Tweet Log in with Facebook Your name or email address: Here are the tests I made to check the disk state: $ ioscan -kfnC disk $ pvdisplay ?v /dev/dsk/c2t2d0 (NB: Physical extents status must be: current) $ diskinfo -v /dev/rdsk/c2t2d0 $ Some digits will represent different information for SCSI errors versus non SCSI errors. this content
In short, that's a drive I would not trust with data. The Current_Pending_Sector tells you how many the drive has already recognized as failed, but hasn't remapped. Next Previous Contents 21. What I'd do though, is look at the SMART info on the disk(smartctl -a /dev/da4). https://community.hpe.com/t5/System-Administration/Getting-SCSI-Read-error/td-p/4657517
Three had already failed SMART self testing so badblocks errors were expected, and duly received, from those. What can I do? No, create an account now. Character Device: # ll -R /dev/ | grep 188 | grep 0x000000 crw-r----- 1 bin sys 188 0x000000 Oct 11 07:15 c0t0d05.
Possible values are:
Function | Error | Description =========|==============|============================================= open | ENXIO | not a valid device | EACCES | access mode is not read/write (O_RDWR) | EBUSY | device Bit odd it should start playing up on a pass other than 1. Indicates that the target aborted the command. | | | The initiator may be able to recover by trying the command again. | |--------+--------------------------------------------------------------------| | Ch | EQUAL. Scsi Error Codes Offline surface scan supported.21.4 Host codes The following host http://ohlandl.ipv7.net/errors/error_11.htm COMMAND TERMINATED.
Error handling The functions open, ioctl, write and read can report errors. Scsi Asc Ascq Indicates that the removable medium may have been| | | changed or the target has been reset. Indicates that the source data did not match the data| | | read from the medium. | |--------+--------------------------------------------------------------------| | Fh | RESERVED. | +=============================================================================+
ioscan is showing NO_HW that means your disk is bad,2)How to solve? Pfa Threshold Reached Would you even consider accepting it? Block device: # ll -R /dev/ | grep 31 | grep 0x000000 brw-r----- 1 bin sys 31 0x000000 Jul 15 16:25 c0t0d0 Or:b. See section midlevel codes 21.2 Status codes The following status codes from the SCSI device (defined in scsi/scsi.h) are available.
Value | Symbol ======|===================== 0x00 | GOOD 0x01 |
Scsi Asc Ascq
Hardware recommendations • RAID5/RAIDZ1 is dead Read my guide! http://www.mpc-forums.com/viewtopic.php?f=1&t=68170 SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was Scsi Sense Key If you create a feature request at bugs.freenas.org, post the issue number here.Click to expand... Scsi Sense Codes Decoder Advertise Privacy Terms FAQ Contact © Copyright 2002 - 2016, MPC-Samples.com.
The Pb should then come from the internal disks (SEAGATE T318203LC). news Well that's a bugger. bigwavealex, May 1, 2014 #12 cyberjock Moderator Moderator Joined: Mar 25, 2012 Messages: 19,103 Thanks Received: 1,645 Trophy Points: 161 That Raw_Read_Error_Rate should be good enough to quality for a return.. Auto Offline Data Collection: Disabled. Aborted Command - Data Phase Error
Hardware recommendations • RAID5/RAIDZ1 is dead Read my guide! Fedex dropped by my house and I kicked them all very hard for you. PS: how to check if these disks are SCSI or IDE one ? http://wx2me.com/scsi-sense/scsi-sense-medium-error-asc-11-0-unrecovered-read-error.php This | | | would be the case for a successful command or a command that | | | received CHECK CONDITION or COMMAND TERMINATED status because one | | |
To make matters worse it passed the last long smart test, which means it doesn't qualify for an RMA right now. Scsi Check Condition Codes This status shall be returned whenever the target terminates the current I/O process after receiving a TERMINATE I/O PROCESS message (see 5.6.22). you need to replace the diskSuraj 1 Kudo Reply senthil_kumar_1 Super Advisor Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content
Thanks a lot for any help.
Showing results for Search instead for Do you mean Menu Categories Solutions IT Transformation Internet of Things Topics Big Data Cloud Security Infrastructure Strategy and Technology Products Cloud Integrated Systems Networking Only you can prevent flame wars! i IanWorthington, May 9, 2014 #16 survive Super Moderator Moderator Joined: May 28, 2011 Messages: 857 Thanks Received: 22 Trophy Points: 26 Occupation: Senior Systems Engineer Location: Missouri, USA IanWorthington Scsi Sense Data Decoder Seatools works on pretty much any drive and a pic from that showing failed drive has never failed to get a return for me.
This status is the combination of the CONDITION MET and INTERMEDIATE statuses. CDB: 88 00 00 00 00 01 cf 06 db 00 00 00 01 00 00 00 Apr 27 19:15:08 freenas kernel: (da4:mps0:0:4:0): CAM status: SCSI Status Error Apr 27 19:15:08 This is the major number of the device in question. check my blog Yes, my password is: Forgot your password?
Extended self-test routine recommended polling time: ( 552) minutes.