This can happen when the disk supports an older standard or doesn’t adhere to the standard completely. Then replace da3 and start another resilver.If da3 on port 4 is the drive being resilvered right now, then report back on that. This includes SCSI interface parity error, controller failure or device failure. 5h Illegal Request Indicates an illegal parameter in the command descriptor block or in the additional parameters supplied as data IronWolf NAS: The Power of Agility: IronWolf and IronWolf Pro, for Everything NAS. have a peek at these guys
This sense key may also indicate that an invalid IDENTIFY message was received. Common sense keys are: 1h Recovered Error — informational only 2h Not ready — temporary error, need to wait it out 3h Medium Error — may work if retried, disappears after The most common format is the fixed format and most of the direct decoding instruction below will be about the fixed format the descriptor format is more complex and less frequent Last Page Forums Welcome to our community forum! https://forums.freebsd.org/threads/51534/
It also is taken to mean that the problem is not permanent and doesn’t afflict the entire disk only some area of it. Are there any logfiles that could give some clues? It is entirely possible that the command that returned with an error is not at all at fault and that everything is just fine with it but that a previous command
The normal BER for SCSI links is around 10^-15 and so about 1 error per day at full data-rate of about 6Gbps is perfectly acceptable, above that it really depends on If you need to get a message to me or email me for any reason, click . What's going wrong? Data Phase Error Since SCSI is a client-server protocol there is no other way for the device to tell you that something changed without piggy-backing on another request which is exactly what happens here.
At some cases a retry to read the data may get the data eventually but it doesn’t have a high likelyhood and it incurs a great penalty in time since normally Scsi Asc Ascq I changed it and now it installed. oebeleUser12 postsPosted on 1 March 2011 @ 22:49also, I don't have another disk in the system to boot from (apart from a CF-card that I would like to take out of you could check here SCSI Sense Key Chart The SCSI Request Sense command is used to obtain sense data (error information) from a target device.
Ch Equal - Indicates a SEARCH DATA command has satisfied an equal comparison. Scsi Error Codes You may view my resume in PDF or Word format. Powered by phpBB Forum Software © phpBB Limited Seagate ␡ Sign In as Consumers & Non-SPP Resellers Partners & Suppliers ␡ My Dashboard My Profile Logout ␡ EXTERNAL One important distinction about a sense buffer is wether the sense is about the command that failed with the sense or a previous command.
Stream Expand Your Tablet and Phone. http://forums.nas4free.org/viewtopic.php?t=10552 The sense key is the key to understand the error code. Scsi Sense Key Operator intervention may be required to correct this condition. 3h Medium Error - Indicates the command terminated with a nonrecovered error condition, probably caused by a flaw in the medium or Scsi Sense Codes Decoder I have removed my address and my phone number.
If not: It looks like da3, which is on port 4, is having trouble. http://wx2me.com/scsi-sense/scsi-sense-deferred-error.php When multiple recovered errors occur, the last error that occurred is reported by the additional sense bytes. This tells us it was a write that failed and that the disk is suggesting to reassign the sector. Using a different (preferably internal) CD/DVD optical unit would probably resolve this issue, but there is an alternative: You could make a bootable USB stick with the instructions over here: http://zfsguru.com/forum/zfsgurusupport/84oebeleUser12 Scsi Sense Data Sense Key 3 Sense Code 11
Take a look at the following example: f1 00 03 02 DD 7E BF 18 00 00 00 00 0C 03 00 00 00 00 00 00 03 0C 03 00 The details both formats provide are the same just the decoding mechanics are different. It could also be some other device, like card reader or other 'obscure' hardware connected to your system; disconnect as many things and disable useless stuff in BIOS (though be careful; check my blog FreeNAS) install I'm getting these messages, only with ZFSGuru there are no more reads from the cd and the installation doesn't continue.
FireCuda PC & Gaming – SSHD: Seagate FireCuda: A Ferociously Fast Hard Drive. Scsi Check Condition Medium Error A medium error means that you tried to read or write data and the disk failed. The first bit of the first byte that is lighted says that the information field has meaning and in the case of a medium error (sense key 3h) the meaning is
A Not Ready sense is returned when the device is powering up and not yet ready to really respond to anything serious, such as when an HDD is still spinning up If the disc drive detects an invalid parameter in the additional parameters supplied as data, the disc drive may have already altered the medium. Dh Volume Overflow - Indicates a buffered peripheral device has reached the end of medium partition and data remains in the buffer that has not been written to the medium. Aborted Command - Data Phase Error If the disk is configured to auto-reassign than a write to that area will cause the disk to reassign and the problem will be gone, if the disk is not configured
Versatile. The next part is the ASC and ASCQ these are found in bytes 12 and 13 (13 and 14 if counting from 1). Either the command is invalid or it is unsupported by the disk. news this provides basic information about the error check the additional sense length.
Examples for this can be when MODE SELECT is used to set Mode Parameters, when an initiator is lost and then you get an I_T_L NEXUS LOSS or several other such The ASC/ASCQ are listed at the T10 ASC/ASCQ page. Please help today!Produce and hosting N4F does cost money, please consider a small donation to our project so that we can stay offering you the best.We really do need your support!We These explain in somewhat more detail the specifics of the problem.
You can get the Changeable Mask for MODE SELECT with MODE SENSE to see if this is the case. Operator intervention may be required to correct this condition. 3h Medium Error Indicates the command terminated with a non-recovered error condition, probably caused by a flaw in the medium or an To circumvent this, format any other disk in the system with GPT, and boot from that. Disk Survey Surveying the disks of the world RSS Blog Archives Survey site Knowledge Base Contact Understanding SCSI Sense This page is about decoding and interpreting the SCSI sense
Disc Drive Sense Keys SCSI Disk Drive Sense Keys Key Sense Key Description 0h No Sense - Indicates there is no specific Sense Key information to be reported for the disc The attention needs to be taken care of and the command that was unfortunate enough to be failed for this can be retried. This includes SCSI interface parity error, controller failure or device failure. 5h Illegal Request - Indicates an illegal parameter in the command descriptor block or in the additional parameters supplied as Under some error conditions this may persist for some while and if it persists for more than 30 seconds or so it is likely to be a failure already.
ASC and ASCQ Codes Category Key ASC ASCQ Error Condition No Sense 0 00 00 No error 0 5D 00 No sense - PFA threshold reached Soft Error 1 01 00 You may want to peruse them to find how to turn on or off this behavior. Some communication failures when they are rare are no importance and can be assumed to happen but if the failure is common enough it should be reported to be fixed by If the disc drive detects an invalid parameter in the additional parameters supplied as data, the disc drive may have already altered the medium.
I've imported the existing pool, but it still it says 'non-bootable' in Install and when I try to install anyway it fails with this message: [ZFSGURU-INSTALL] Starting installation with configuration: distribution