Release the printer locking screw. If the voltages are correct, and the cables are undamaged and correctly connected, causes of this error may be a defective cable, a defective printer, printer control board or the main If these actions have no effect, replace the dispensing mechanism. 203 SPED keypad is not replying to main board Status valid only for units with SPED keypad device installed. 1. Press and hold the Resume button (triangle inside a circle). i thought about this
Proceed by following procedures for error code 109 or 112. 108 Unexpected note at double detect A note has been detected in the double detect sensor without being detected at the Do several test dispense operations. Place all belts on their rollers and gears.
If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 112 Timeout waiting for leading edge at reject A note that was expected to be seen at Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 115 Diverter timeout on purge 1. Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser.
Or just drag it here! It is usually caused by attempting to dispense currency that is unacceptable or currency that has not been properly prepared. 1. It does not matter if the capacities (Standard or High) do not match. or it's affiliates.
If the cables are undamaged, the main board or electronic journal may be defective 159 Electronic journal test feature failed 1. Don't believe you can get the drivers but try Konicaminolta Web site. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. If the error clears, put the cash dispenser in service. 5.
Note: This error code is often caused by a SPED tamper. https://forum.fortinet.com/tm.aspx?m=141536 If these actions have no effect, replace the dispenser. 45 Diverter error This error occurs when the diverter is in the wrong position during a dispense.1. If the error clears, put the cash dispenser in service. 5. Remove jammed currency. 2.
berks county scanner freq bunya mountains national park... Get More Info I can't find out meaning of 2 flashing yellow lights. Edit Close Save changes Attachments: Added items Uploading: 0% my-video-file.mp4 Complete. Please enter a valid email address.
Put more currency in the cassette and repeat the “learn note thickness” command. Wait until the preparatory operation is complete; it takes about one to two minutes. Turn off the printer and then turn it on again Thanks. useful reference Consult 183 Receipt printer paper is low 1.
Test the dispenser by completing several test dispenses. 4. Clear the error. Inspect electronic journal to dispenser communication cable for damage.
On an 8 bit machine, such as 9100 or 9600, choose Diagnostics>More>More Keypad>Clear Tamper. 240 SPED Self Test Error The SPED has returned an error during self test. 1. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3. Clear the error. Share on Facebook Share on Twitter Share on Google+ Share on Pinterest Share by Email × Question about Canon PIXMA Pro9000 InkJet Photo Printer Open Question How do I fix service
Need a qualified technician to get the firmware if still available. I've tried truing it off and unplugged it from the mains supply but it still does the same. Removing Ink Cartridges: After confirming that the printer is powered on, open the scanning unit (printer cover). this page bala cynwood pa call the cards.
Tip: The max point reward for answering a question is 15. 0 characters Video Photos Link Replacement Parts Add Upload Upload × × Draw a box over the problem!! Clear the error. 3. Inspect main board to electronic journal communication cable for damage. Verify that all sensors are operation correctly.
If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3. It the status clears, place the cash dispenser in service. Reset the cash dispenser. If these actions have no effect on dispenser operation, replace the dispenser mechanism.
If these actions have no effect, replace the dispenser. 51 Accountancy error A mechanical failure has occurred.